Search results

Burnsville ms. Home of the big ditch (the Tombigbee waterway) about 12 mi. from J.P. Coleman park

chad, redman here i,ll take the pyrometer if it has the leads. Just let me know how to pay.

Congrats Newell the two outside are probably hooked together in the trolling motor plug or the motor to get your 12-24V. I had a XTB-21 before the 2003 these are nice boats. Just weight the off side and enjoy it.

thats right mine has the breaker fastened on the wing nut and accessories on the other. If you have voltege on the bat, side and not on the other the breaker is kicked or bad. You can't see the reset tit its on the very end real small about 1/8" dia. feel or take it off the wing nut if its this...

that should be a cicuit breaker. check on each end and see if there is a little tit sticking out, if it is see if you can push it in and reset it.

Buy it from Allison, everyting comes with it. new wheel and all. I don't thinkthis includes the trim switch. I bought the double (turn signal type on both sides of the wheel) its nice too.

fastbasser mine is a 2003. wasn't much trouble at all. the biggest job is getting the old cables out and I think most just hacksaw the ends. just tie a string, wire etc. to the old cable to pull the hoses in with. I ran mine out he back with lines and such and crossed them at the cylinder. made...

ran the boat today, man that sure beats wrestling with the cabels. the slack on the motor end isn,t enough to even worry about. probably less than 5/8" movement on the wheel end.

Ally the slack seems to be at both. you can shake the moto and see just a little movement on cylinder to rod, just a few thousants. I wouldn't think it would be over 1/4" at the propshaft. I will check tommorow. I don't think it will effect the handling. Just wondering if this was normal.

run $1345 with the double trim switch. Be carefull and don't spill that oil! you don't want to waste much of that stuff//

Just finished putting hyd. steering from Allison on my 03 I have bleed the system out. it has just a very very small amount of movement in the cylinder. is this normal or do i still have a little air?

ok, here I go again. just got my boat back from the shop having my motor checked out. everything ckecked out good by a good certified merc. mech. seems like my problem on the rpms is that everything I see says that max rpms for this motor is 6200-6500 r's (98 225 supermag) that is what the tag...

my 95 say tourniment to does anyone know of any other differences in them?????

thanks all. That's kind of what I have been thinking about. Have been there with the hot rods, had 468 big blouck 67 SS chevelle more compression most of the times means more air,more gas, more exaust,more trouble, may just run it and enjoy it. thanks again for all the input!! I am thinking...

the motor is bone stock. it don't seem like it has ever run like I read on these post. I hardly ever run wide open, I'm moving on toward those senior citz. discounts. know what I mean? but I have a young son 35 or so that dont care to air it out. have the sporsmaster at J.C."s getting it woked...

Thanks John for the reply, if I just change the gasket to a thinner one what would this give me ond which one do I use? enjoy reading all the post and it seems that you may know what you are talking aboute>>

I'm runnung a 95 2003 hull with a 225 super mag. 25 tempist prop 1/4 below the pad heavy load ( two men tackel ect) running 80 gps at about 6400 rpm my question is on outboard how do you tell when they are hitting the limiter the other question is how much in thousants can you shave the...

Thanks everyone for the replys. I have always ran the lowrance products. sort of like to stay with them. i enjoy this site very much since i have retired and have time to watch it now. Have a XB2003 with a 225 supermag really enjoy it. I hardly ever air it out but I might just want to see what...

Does anyone make a gps sonar combo with a recall for top speed that anyone knows of? thanks in advance

I know i'm a little slow, but I can't get the search feature to work, looking for imformation on the baker mods on the sportsmaster. thanks